Q–I need to rebuild a simple interior staircase. What is the simplest and easiest way to tackle this project? When you cut those deep notches in the side stringers, does that weaken the staircase? Are there any products or techniques that can simplify stair construction?
A–I sure hope that you paid attention in your math classes and that you have some basic carpentry and sketching skills. You are going to need all of these skills to successfully complete the project.
Stair construction can be very challenging and confusing. It is important that you follow all safety recommendations and building code requirements. If you pay attention to detail, you can complete the staircase in one day. (If not, you better keep a ladder nearby.)
First, take a notebook and make a simple cross-section drawing of the existing staircase. Note the vertical distances between each step and the vertical distance between the first and last step and each floor level. Measure the depth of each tread at the same time and record these measurements. Double check your measurements and drawing for accuracy. Note any gaps between each side stringer and where these components touch the bottom floor and the subfloor header.
If you’re lucky, the vertical measurements between each stair tread and the depth of the treads will be consistent. Using a rectangular piece of cardboard–10 inches high by 14 inches long–you can make a stair-angle guide that will allow you to recreate the top and bottom stringer cuts and the position of the treads before you remove the old staircase.
Place the cardboard rectangle against one side stringer with the 14-inch edge resting on one of the middle stair treads. Slide it back so the 10-inch edge just touches the stair tread nosing above. Place a yardstick or other long straightedge on the stair tread nosings. Slide it up against the piece of cardboard. Use a pencil and trace a line on the underside of the straightedge. The result should be a triangle whose sloping leg connects one stair tread nosing with the one below. The bottom leg of the triangle will be your tread length and the vertical leg will be the riser height.
As you demolish the old staircase, make every attempt possible to salvage the side stair beams or stringers. The top and bottom angle cuts on these side stringers are the most challenging part of the project. If there were no gaps where the old ones met the floor and subfloor header, you can use the old stringers as a template. This will save you hours of agonizing work and wasted lumber.
Trace the pattern of the old stringer onto your new side stringer. I like to use 2-by-10 or 2-by-12 lumber for strong staircases. I never cut notches in my stringers because this weakens the staircase. Cut along the traced lines and place the stringer in position. It should fit perfectly. Temporarily tack the stringer into position so it will not fall.
Starting at the top of the stringer, use your triangle template to mark the location of the top of each tread and the face of each stair tread nosing. Make adjustments as necessary to match your original drawing. Remember, the sloping line of the template must be parallel or in line with the edge of the stringer at all times.
There are some wonderful wood and steel products that simplify stair construction. You can purchase adjustable triangular wood blocks that screw or nail to a 2-by-6 or 2-by-8. Once they’re applied to the stringers, you end up with the notched look but not the traditional weak staircase. These triangular wood assemblies allow you to create an infinite amount of riser and tread combinations to fit any situation.
You can also purchase simple, L-shaped metal brackets that are nailed or screwed to the side stringers. The stair treads rest on these strong metal brackets. These handy devices eliminate any need to notch the stringers or plow grooves to accept the treads. They can be found at most lumber stores that sell metal deck framing components.
———-
Have questions about the remodeling process? Write to Tim Carter, c/o The Chicago Tribune, P.O. Box 36352, Cincinnati, Ohio 45236-0352. Questions will be answered only in the column.
For step-by-step, illustrated instructions of how to build interior and exterior staircases and a list of manufacturers of stair components, send $2 and your name and address to Tim Carter at the above address. Ask for Builder Bulletin No. 210.
For a list of past Builder Bulletins and a wide variety of individual job bid sheets, send a business-size, stamped, self-addressed envelope to the same address.
